SunPumps SCP Pool Pump

These centrifugal pumps are designed specifically for pool water circulation. The SCP series pumps are equipped with heavy duty permanent magnet, DC motors. The pump ends are constructed from high performance thermoplastic and are extremely resistant to chemicals as well as mineral and algae deposits.

For added protection, a basket strainer is incorporated into the suction side of the pump. They can also be used to fill open tanks, aerate ponds, circulate water for aqua culture or irrigate small farms.

Inlet and discharge ports are 2" NPT and they operate at 45 to 90 VDC. SCP 42-47-10 operates up to 120 VDC and can pump 93 gpm at 0 psi.

Use with SunPump Control PCB-120 (075-03041) located in the above table.

MODEL	HP	SCP POOL PUMPS									PART NUMBER	PRICE	PURCHASE
		amps	Flow rate at 0 psi	Pressure max psi	amps	Flow at 0 psi	Pressure max psi	amps	Flow at 0 psi	Pressure max psi
		50 VDC			75 VDC			90 DC
SCP 47-25-07	3/4	4.9	80 gpm	9	7.1	97 gpm	14				075-03066	$1,215
SCP 62-37-10	1	4.9	108 gpm	10	7.1	108 gpm	15	9.32	124 gpm	21	075-03070	$1,245
MODEL	HP	90 VDC			105 VDC			120 DC			PART NUMBER	PUICE	PURCHASE
SCP 56-28-10	1	3.0	71 gpm	12	3.75	83 gpm	14	4.6	96 gpm	18	075-03072	$1,245
SCP 70-37-10	1	4.6	104 gpm	12	5.9	120 gpm	18	7.7	135 gpm	22	075-03074	$1,245
SCP 87-28-10	1	6.7	134 gpm	14	8.7	153 gpm	18				075-03076	$1,245
MODEL	HP	120 VDC			150 VDC			180 DC			PART NUMBER	PUICE	PURCHASE
SCP 95-35-15	1.5	3.7	119 gpm	12	5.3	145 gpm	18	7.2	170 gpm	24	075-03078	$1,645

TOP

SunPumps SC 24-116 Centrifugal Surface Pump

This pump can be used for water lifts of up to 150 feet.

SunPumps SC 24-116 centrifugal surface pump is the centrifugal section of a convertible jet pump.

It will produce 24 gpm at 116 feet of head, operating at 120 VDC. This pump can also be used as either a shallow well or deep-well jet pump with the addition of a jet adapter.

This SC centrifugal pump is used as a panel-direct centrifugal booster pump. See the chart for basic sizing or call for a complete system quote.

Use with SunPump Control PCB-120 (075-03041).

psi head (feet) amps gpm motor watts PV watts 5 12 5.83 42.4  700 875 10 23 11.3 40.7 1360 1700 20 46 11.2 37.1 1310 1686 50 116 9.9 23.9 1195 1494 65 150 8.3 9.2 998 1248

SC 24-116

075-03103

$1,495

TOP

SunPumps Solar Jet Pump

The SunPumps SJT series pump is designed for use in shallow water wells.

It has excellent suction lift capabilities and is primarily used to fill open storage tanks. It operates
directly on 200-500 watts of solar modules at 60-90 VDC.

Use with SunPump Control PCB-90 (075-03035)
 

60 VDC 75 VDC 90 VDC Module watts Flow rate (gpm) Pressure (psi) Module watts Flow rate (gpm) Pressure (psi) Module watts Flow rate (gpm) Pressure (psi)  195 15.6 0 356 19.4 0 546 23 0 179  11.1 5 338 016-03   5 513 18 10 155  4.3 10 315 12 10 486 14 15 139 0 12 281 6.5 15 450 9 20       244  0 19 394 0 27

SJT 12-40

075-03117

$1,445

TOP

SunPumps SJ Jack Pumps

This jack pump can be used for water lifts of up to 1,000 feet of head.

SunPumps SJ series jack pumps are either Jensen or JC brand pumping units retrofitted for solar power. They can efficiently pump from wells with a depth of up to 1000 feet.

These pumps are custom built and tested for your specific application.

Call for more information. 

This pump can be used for water lifts of up to 440 feet.

The Slowpump can push water as high as 450 vertical feet. It runs on very little power, with or without batteries, to supply between 200 and 2600 gallons of water per day. The positive displacement vane pump mechanism is housed in forged brass, and lasts for years of all-day running. 5 micron filtration is required to protect the pump.

For PV-direct (no batteries in system) array, watts must exceed pump watts by 20% or more, and a linear current booster controller is required (page 123). The sizing chart shows the gallon per minute (GPM) output from the pump and power (Watts) consumed by the pump for various vertical lifts. (This is the lift from the water level to the top of the tank that the water is pumped to). The performance in the chart is measured at array direct voltage. The peak power voltage of typical solar modules is 17 Volts.

A battery powered system will have 15% lower flow and wattage. To estimate gallons per day delivery, multiply GPM figure by 60 and then by the peak sun hours per day in your location. Using a tracker with your solar modules will give you approximately 40%-50% more water in the summer. Slowpumps are available with 1/2 HP motors for greater lift.

NOTE: Pumps listed 12 or 24 Volts may be used with batteries or array direct. The 36PV/48B pumps can be run PV direct with a 36V array or from a 48V battery bank. For 120VAC operation order the desired pump and the Slowpump AC Option.

Warranty is one year.

TOP

SCB Pressure Booster Pumps

This pump can be used for water lifts of up to 277 feet of head.

SunPumps SCB series pressure pumps are multi-stage centrifugals designed primarily for boosting pressure from surface water as long as the water supply is above or no more than 3' below the level of the pump.

They are ideal pumps for home pressure systems, sprinkler systems or inline booster pumps.

SunPumps SCB series pressure pumps are very high quality, maintenance-free, DC pumps specifically designed for standalone water delivery in remote locations to be powered from batteries.

Allow 2 weeks for delivery.

Capacities in U.S. gallons per hour at discharge pressure or feet of lift (head)
Model number	Nominal volts	Watts required	Gallons per hour											PART NUMBER	OUR PRICE	Purchase
			psi
			20	30	40	50	60	70	80	90	100	110	120
			head in feet
			46	69	92	116	139	162	185	208	231	254	277
SCB 6-40P-24	24	300	510	420	360	240	80							075-03132	$1,195
SCB 8-40P-24	24	400	590	510	470	400	310	210	70					075-03134	$1,235
SCB 10-40P-24	24	600	828	714	582	420	222							075-03135	$1,286
SCB 20-25P-24	24	900	1483	949										075-03137	$1.254
SCB 12-60P-48	48	900	930	870	810	770	710	660	600	520	450	360	220	075-03139	$1,397
SCB 24-50P-48	48	1600	2226	1996	1740	1466	1140	683						075-03141	$1,397

TOP

Flowlight Booster Pump

This pump can be used for water lifts of up to 20 feet.

The Flowlight Booster Pumps provide "town pressure" for home water supplies where 12, 24 or 48 volt power is available. They have a longer life and greater flow rate than Flojet and Shurflo booster pumps and they use less than ½ the energy consumed by an AC jet pump running on an inverter.

The Flowlight Booster pump will be damaged if it runs dry or is used for pumping rusty or dirty water, so order a filter and dry run switch. To make installation and service easy, flexible hose connectors with ¾" threaded adapters are included. A minimum 40 gallon pressure tank is required for all Flowlight booster pump installations (available locally from a pump supplier).

The standard Flowlight model has the highest flow. Use only where suction lift is less than 10 feet.

The low flow model has a higher pressure capacity and should be used where suction lift is greater than 10 feet or where suction pipe is less than 1" inside diameter. Maximum suction lift is 20 feet at sea level for low flow model.

Use the 115 VAC pump where DC wiring is not feasible, like long wire runs. It has similar high efficiency and low starting surge. It can run on less than a 500 watt inverter.

Dimensions: 016-05" in length.

1-year warranty.

Description	Voltage	MAX. GPM	Pressure (PSI)	DC Amps	Weight (lb.)	PART NUMBER	OUR PRICE	Purchase
Standard 12V	12 VDC	4.5	30	13.0	15	075-04125	$590
			40	15.0
			50	016-00
Standard 24V	24 VDC	4.5	30	6.5	15	075-04127	$590
			40	7.5
			50	8.0
Standard 48V	48 VDC	4.5	30	3.5	15	075-04129	$845
			40	4.0
			50	4.5
Standard 12VAC	120 VAC	4.5	30	1.5	15	075-04131	$695
			40	1.6
			50	1.7
Low Flow 12V	12 VDC	3.4	30	10.0	15	075-04121	$553
			40	11.0
			50	12.0
Low Flow 24V	24 VDC	3.4	30	5.0	15	075-04123	$553
			40	7.5
			50	8.0

TOP

Shurflo 2088 Pressure Pumps

This pump can be used for water lifts of up to 100 feet.

These positive displacement diaphragm pumps make excellent household pressure pumps if you need less flow than the booster pumps on the previous page deliver. The Shurflo 2088 pumps up to 3.6 gallons per minute, are designed for continuous duty operation with addition of optional heat sink, and they can be run dry without harm. They have a built-in pressure switch and ½" male pipe thread ports for easy connection to common plumbing fittings.

Home pressurization installation requires a pre-charged water tank. For general water pumping, this pump can self prime to 10 feet and lift water up 100 feet. The 120 volt AC version can run on a 200 watt inverter and can be 1000 feet from the inverter using 12 gauge wire.

Dimensions: 4.45" x 12.4" x 5".

TOP

Use the 2 Gallon Pre-charged pressure tank to extend the life of your Shurflo pump. The tank helps provide a smooth flow in your pumped water system and reduces motor heating and pressure switch wear by decreasing the number of on/off cycles. Internal bladder is precharged to 20 PSI.

Adapters fit the Straight Pipe Thread on the 2088 pumps and allow connection of tapered pipe thread fitting. Right angle fittings have wingnut fitting that can be tightened by hand. Straight fitting has a hex nut cast into it.

Shurflo PART NUMBER	Description	PART NUMBER	OUR PRICE	Purchase
3400-002	Vertical 2 Gallon Pre-Charged Pressure Tank - Stainless steel with 3/4" male NPT port	075-05730	$130
170-061-20	Twist-on Water Strainer - 50 mesh screen 1/2" FPST inlet	075-05784	$10
8-035	Adapter w/Wingnut - Right Angle 1/2" FSPT to 1/2" NPT for 2088 Pumps (2 units)	075-05735	$5
8-155-01	Adapter w/Wingnut - Right Angle 1/2" FSPT to 5/8" Barb for 2088 Pumps  (2 units)	075-05763	$5
8-205-00	Adapter - Straight 1/2" FSPT to 1/2" NPT Male for 2088 Pumps  (2 units)	075-05760	$5
34-006	5" Heat Sink for continuous duty pump operation	075-05766	$24

TOP

SunPumps SPB Piston Pump

This pump can be used for water lifts of up to 15 feet.

SunPumps SPB series triplex piston booster pumps are high quality, positive displacement piston pumps designed for medium to high heads where flow rates are low to medium but reliability is a must. They are surface-mounted pumps designed to pump from cisterns, lakes, rivers or above-ground tanks.

They have good suction lift capability, up to 15 feet at sea level.

Sunpumps SPB series triplex pump systems come as a complete package including the pump, motor, mounting base, pulleys, geared belt and belt guard. These pumps are custom built and tested for your specific application.

SunPumps have pumps in operation boosting water as high as 2300 feet vertically.
 

TOP

This pump can be used for water lifts of up to 22 feet.

Pumps more water with less power. Out lasts 10 small diaphragm pumps. Tolerates dirty water. Life expectancy is 20 years with 2 to 6 year owner performed maintenance schedule. Cast iron body, brass cylinder and valve seats, oil bath crankcase, and pressure relief valve.  Lifts water from shallow wells. 

A foot valve is required for suction lift. 

Maximum 22 feet suction, and push to 220 feet (95psi) or to standard pressure tank.  Inlet 1-1/4 inch, outlet 1 inch pipe thread.  Permanent magnet DC motor models available for battery or direct solar power. 12, 24, 48, or 90 volt DC, or 120 or 240 volt AC.

Use battery models for home system.

Use solar direct with panels and with 15 amp LCB for pumping when no battery system is nearby.

Two year warranty.

TOP

WE ACCEPT...

All transactions made on this site are secure and Hacker Safe. All Our Payments are processed through PayPal, a trusted company owned and operated by eBay.com
Prices are usually correct but subject to change, if there has been any change we will notify you .  

This page designed and maintained by Terry R. Wolff