| |||||||||||||||
| CONTROLLER AND INVERTER ACCESSORIES | INPUT-OUTPUT BYPASSES |
FLEXWARE SYSTEM ENCLOSURES |
BATTERY RACKS |
MISC. ACCESSORIES |
Remote Monitor and Control
The OutBack MATE is a complete system controller and display for both
the OutBack FX2000 inverter/charger and MX60 MPPT PV charge controller. It
provides a display of the operation as well as allows control and adjustment
of the setpoints. The OutBack Mate also coordinates the operation of the
entire system to maximize performance and to prevent multiple products from
conflicting.
A single OutBack MATE is able to connect to multiple FX2000
inverter/charges, MX60 MPPT PV charge controllers and any other OutBack
power conversion and control products offered in the future. A maximum of
ten OutBack products will be able to be connected to a single MATE via CAT 5
/ ethernet type cabling with 8 wire RJ45 modular connectors and the OutBack
HUB communication manager.
The OutBack MATE includes a 4 line backlit LCD display with 80
alphanumeric characters. This allows multiple measurements to be displayed
at the same time and reduces the amount of abbreviations required,
simplifying the operation and reducing confusion. All of the programmed
setpoints are stored in permanent memory to eliminate the need to reprogram
the system after a shutdown or battery replacement.
The OutBack MATE also includes a built-in real-time clock and
calendar which allows programming of the inverter operation based on the
time of day and even day of the week. This can be used to allow the system
to work with time-of-day power rates or to limit a generator's run time to a
specific period of the day or week.
The OutBack MATE also includes an opto-isolated RS232 port with a DB9
jack for connection to the serial port of a PC computer.
OutBack is working with several third-party developers to offer
Windows-based software programs for data logging and graphical display of
the systems operation and performance. This PC computer software will be
available separately and is expected soon.
Specifications
|
|
Remote Monitor and Control
The
MATE2 system display and controllers are complete management tools for
your OutBack Power system. Through the use
of a single MATE2 you can remotely manage and monitor multiple
inverter/chargers, MX60s and any future OutBack power conversion and control
products. The Mate2 is the same device as the Mate, but with a different
case.
The MATE2 is packed full of features to make system management
simple. The easy-to-read 3.1" (8 cm) LCD is backlit for dark operating
conditions. Four soft keys allow easy context-based navigation of menus and
functions. Two hot keys give immediate access to AC and inverter functions.
A built-in clock and calendar function enables timer based programming of inverter and charger operation. This permits you to set the system to work with time-of-day power rates or to limit a generators run time to a specific time period of the day or week.
All of your settings are stored in permanent
memory to eliminate the need to reprogram in the event of a system
shutdown or battery replacement. The MATE2 includes an RS232 port with DB9
jack for connection to the serial port of a PC computer.
Through the use of optional WinVerter software you can perform such
operations as data logging and graphical display of the system's operation
and performance.
Specifications
|
|
Remote Monitor and Control for
boats and RV's
MATE2M Remote Display and System Control Panel, without RS232. Square
Case Black - square panel mount. This is the same device as the OutBack
Mate, but with a different case.
The MATE2M is a complete management tool for your OutBack marine
power conversion system. The onboard CPU coordinates the operation of all
your OutBack system components for maximum performance and smooth system
integration.
A backlit LCD provides a display for sytem monitoring while four soft
keys allow navigation of the menu system and adjustment of settings.
Information for up to 10 inverter/chargers and other OutBack power
conversion equipment is available at your fingertips through the
communications HUB. Your programmed settings are stored in permanent memory
to eliminate the need to reprogram the system in the event of a system
shutdown or battery replacement.
The OutBack MATE2M includes a built in clock and calendar which
allows timer based programming of power system operation. This enables the
user to specify a generator's run time to a specific time period of the day
or week.
Specifications
|
|
TOP
TOP
HUB-4 System Communication Manager
The OutBack HUB-4 system communications manager allows the
interconnection of up to four power conversion devices with the MATE.
The interconnection creates a completely integrated Power System that is coordinated and managed by the MATE.
The OutBack HUB-4 communicates stacking phase, load share, incremental start-up and shut-down information directly between the inverters. Interconnection cabling is standard ethernet CAT5 eight wire with RJ45 modular jacks.
The HUB is powered via any inverter or MX60 charger controller.The OutBack HUB-4 communication manager allows the MATE to control any combination of four FX series inverters/chargers and OutBack charger controllers.
Weight: 3 lbs
The OutBack HUB-10 system communications manager allows the interconnection of up to ten OutBack power conversion devices with the MATE.
The interconnection creates a completely integrated Power System that is coordinated and managed by the MATE.
The OutBack HUB-10
communicates stacking phase, load share, incremental start-up and
shut-down information directly between the inverters.
Interconnection cabling is standard ethernet CAT5 eight wire with RJ45 modular jacks. The HUB-10 is powered via any inverter or OutBack charge controller.
The OutBack HUB-10 allows the MATE to control any combination of eight FX series inverter/chargers and OutBack charge controllers.
Outback RTS Remote Temperature Sensor for MX60 charge controllers and
OutBack inverters.
The OutBack Remote Temperature Sensor (RTS) is a necessary tool
for proper battery charging. All OutBack products with integrated
battery charging have a temperature compensation system built-in
which benefits from the installation of the optional RTS. The RTS
ensures that your OutBack system knows the precise ambient
temperature so that it can recharge your batteries safely and
efficiently. Systems with multiple OutBack products connected to
one HUB4 or HUB10 require only a single RTS to be installed.
Weight:1 lb
Multi-Stage Battery Charging (5
Stage)
|
||
| Batteries are a key
component in backup and off-grid systems, often serving as the only
energy storage device. To guarantee that they function properly it
is important that your batteries are maintained. A chief part of
this maintenance is proper charging. Your batteries should always be
maintained above a 50% level of charge and receive a complete
recharge once a month to ensure operation at peak performance.
Prolonged use of the battery below a 50% state of charge will
adversely affect the long-term health of the battery and can result
in premature failure. The multistage charging process ( 5 stages) uses several regulation stages to allow fast recharging of the battery energy storage system while ensuring a long battery life, high performance and efficient operation of the |
Charge Controller,
the batteries enter the (3) FLOAT stage where they are given
a maintenance charge until there is no excess renewable energy. The
FX or VFX inverter/charger will go into (4) SILENT mode where
the charger turns off until the battery voltage drops to the
“re-float” setting. At this point the inverter/charger initiates the
maintenance float charge. This method reduces fuel and utility
consumption. It should be noted that the temperature of your batteries has an impact on the charging process. The OutBack RTS should be used to monitor this. In higher ambient temperatures, the battery charging regulation settings will be automatically reduced to prevent overcharging of the batteries. Conversely, in lower ambienttemperature conditions, the regulation |
settings will be increased to ensure complete recharging of the batteries. Batteries are composed of a group of individual cells. Through normal use, the charge of each individual cell will not be equal to the other cells. To address this, your batteries should be (5) EQUALIZED either once each month or once every few months depending on usage. During the equalization charge the electrolyte in the battery is stirred up by gas bubbles, which help to create an equal mixture of water and acid. Simultaneously the full cells are overcharged which allows the low cells to “catch up” and all of the active material in the battery to be reconverted to its charged state. Depending on usage, the hardened battery plate material that is no longer active in the battery-sulfation can also be reduced by an equalization charge. |
| overall system. The
charging process begins with the (1) BULK stage, where
maximum current is sent to the batteries until the target “absorb”
voltage is reached and the absorb stage of the charge begins. During (2) ABSORB, the charger provides the batteries with the just enough current to hold at the set voltage for a preset amount of time. Following this cycle, the charging system changes between available OutBack charging products. Using a FLEXmax Series
|
|
|
The OutBack Power Systems FLEXware Surge Protector is a seamlessly
integrated
balance-of-system component for the FX Series Inverter/Charger. The FLEXware
Surge Protector was designed by OutBack engineers specifically for OutBack
FX
Series Inverter/Chargers, and provides multiple levels of protection for the
vital
electrical components of the Inverter/Charger in the event of an electrical
surge
or nearby lightning strike. The sophisticated design allows for both AC and
DC
protection on multiple circuits (two AC and one DC) via thermally fused
Metal
Oxide Varistors (MOVs). LED visual indicators provide at-a-glance status
monitoring
allowing system users to determine FLEXware Surge Protector operational
status in
real-time. The FLEXware Surge Protector is designed to operate between 120
to 240
VAC at 50/60 Hz and 12 to 48 VDC. Its multiple mounting configurations allow
it to be
incorporated into any OutBack system. The FW-SP-ACA mounts inside the FW-ACA
for FLEXware 500 and 1000 systems, while the FW-SP-250 is designed to mount
inside
the FLEXware 250 AC Side Breaker Enclosure allowing for quick installations
that keep
your system protected and looking great.
The OutBack Power Systems FLEXware Surge Protector is the only
choice when you want to
protect your FX Series Inverter/Charger from the harmful effects of
transient power surges. Ease
of installation and seamless integration make it the obvious addition to
your OutBack system.
PSX-240
The OutBack PSX-240 auto transformer can be used for step-up, step-down,
generator and split phase output balancing or as a series stacked inverter
to load
balancing auto-former. Incorporating a transformer with 120 volt/30 amp
primary and secondary side, a temperature activated cooling fan and a 25
amp dual breaker in a steal enclosure, the PSX-240 is ready to install in
your
custom application. Use for 120 or 240 VAC 60 Hz systems only.
Powering 240 volt items like deep well pumps with a single 120 volt inverter
is possible
thanks to the PSX-240’s step-up capability. Its step-down feature allows you
to charge your batteries
with a 240 volt generator through
a single 120 volt inverter. The PSX-240’s ability to balance the output of
series
stacked inverter/chargers makes it a critical item when using the OutBack
stacking 120/240 VAC configuration.
The FW-X240 is also available without the enclosure, for installation inside
the FW500-AC or FW1000-AC enclosures.
Field installable kit with color coated wire, all required terminal bus bars and sliding interlock plate.
Triple inverter Input-Output-Bypass for FW1000 - 120/208 VAC output 60 amp 21.6 kW. Includes nine 60 amp 120 VAC single pole DIN mount breakers.
Field installable kit with color coated wire, all required terminal bus bars and sliding interlock plate.
Triple inverter Input-Output-Bypass for FW1000 - 230/400 VAC output 30 amp 20.7 kW. Includes nine 30 amp 230 VAC single pole DIN mount breakers.
Field installable kit with color coated wire, all required terminal bus bars and sliding interlock plate.
Quad inverter Input-Output-Bypass for FW1000 - 120 VAC output 120 amp 28.8 kW. Includes twelve 60 amp 120 VAC single pole DIN mount breakers.
Field installable kit with color coated wire, all required terminal bus bars and sliding interlock plate.
Quad inverter Input-Output-Bypass for FW1000 - 230 VAC output 120 amp 27.6 kW. Includes twelve 30 amp 230 VAC single pole DIN mount breakers.
|
WE ACCEPT... |
||||
|
|
 |
|
|
|
All transactions made on
this site are secure and Hacker Safe.
Your Payments are processed by Solar Taos, LLC
through PayPal, a trusted company owned and operated by eBay.com
Prices in this catalog subject to change without notice.
|
If you are
interested in
quality supplements,
please click on the
above logo. |
 American Sign & Wood Carving |
 Wood Care Product |
